EFEK VARIASI BEBAN PENDINGINAN TERHADAP COEFFICIENT OF PERFORMANCE (COP) MESIN PENDINGIN PADA BOX COOLER  ALAT DISTILASI

Ahmad Akromul Huda; Karyanik Karyanik; Earlyna Sinthia Dewi

doi:10.31764/jau.v8i2.5239

EFEK VARIASI BEBAN PENDINGINAN TERHADAP COEFFICIENT OF PERFORMANCE (COP) MESIN PENDINGIN PADA BOX COOLER ALAT DISTILASI

Ahmad Akromul Huda, Karyanik Karyanik, Earlyna Sinthia Dewi

Abstract

Refrigerator has been widely used by the community and can be found in almost every shop, office building and household. The application of refrigeration machines can also be developed in many other equipment and machines, one of which is in the distillation apparatus. Distillation is a method of separating two substances. A distillation machine using a cooling machine in the condenser will be very helpful, especially for distillation. This study aims to determine the effect of cooling on the performance of the cooling machine. Cooling engine performance coefficient of achievement (COP). Load variations are carried out by adjusting the boiler temperature using a thermostat. In this study, data on the temperature and pressure of the refrigerant flowing in the refrigeration system were taken at four points, namely before entering the compressor, before entering the capillary tube and before entering the evaporator . In this study also used four variations of the cooling load given to the box cooler of 110 °C, 125 °C, 140 °C, and 155 °C. Then the temperature and pressure data is processed to get the COP value every time from all variations of the cooling load. The results showed that the increaseing in the cooling load, the smaller the COP value of the cooling machine. In its effect on the length of time the COP value of each variation of the cooling load increases. The highest COP value in this study was obtained at a cooling load temperature of 110 ºC of 10.69 and the lowest was obtained at a temperature of 155 ºC of 9.38.

Keywords

Box cooler; Coefficient of performance; Cooling engine performance; Distillation; Refrigerator

Full Text:

PDF

References

Anwar, Khairil. 2010. “Efek Beban Pendingin Terhadap Performa Sistem Mesin Pendingin.” Jurnal SMARTek 8(3):203.

BPPT. 2014. Pengembangan Energi Untuk Mendukung Program Substitusi BBM. Vol. 1.

Chen, Lingen, Chih Wu, and Fengrui Sun. 1998. “Cooling Load versus COP Characteristics for an Irreversible Air Refrigeration Cycle.” Energy Conversion and Management 39(1-2):117–25. doi: 10.1016/s0196-8904(96)00119-7.

Emmaputri, Fathia Salsabila, Sarifah Nurjanah, Efri Mardawati, M. Ade Moetangad Kramadibrata, Mimin Muhaemin, Wahyu Daradjat, Handarto Handarto, and Totok Herwanto. 2019. “Kajian Proses Distilasi Fraksinasi Biodiesel Kemiri Sunan (Reutealis Trisperma).” Jurnal Teknotan 12(2):29. doi: 10.24198/jt.vol12n2.5.

Ilminnafik, Nasrul, and Digdo Listyadi. 2013. “Pengaruh Variasi Beban Pendingin Terhadap Prestasi Kerja Mesin Pendingin Dengan Refrigeran R12 Dan Lpg.” Rotor 6(1):30–34 – 34.

Kusnandar, Kusnandar, and Yudhy Kurniawan. 2020. “Perbandingan COP AC Split Kapasitas 1 PK Menggunakan Refrigerant R410a Dan R32 Dengan Variasi Kecepatan Fan Evaporator .” TURBULEN Jurnal Teknik Mesin 2(2):50. doi: 10.36767/turbulen.v2i2.553.

Mainil, Rahmat Iman, and Afdhal Kurniawan Aziz. 2015. “Penggunaan Modul Thermoelectric Sebagai Elemen Pendingin Box cooler.” Rekayasa Dan Aplikasi Teknik Mesin Di Industri Kampus ITENAS 1(December):44–49.

Marjoni, Mhd. Riza. 2014. “Pemurnian Etanol Hasil Fermentasi Kulit Umbi Singkong (Manihot Utilissima Pohl) Dari Limbah Industri Kerupuk Sanjai Di Kota Bukittinggi Berdasarkan Suhu Dan Waktu Distilasi.” Pharmaciana 4(2):193–200. doi: 10.12928/pharmaciana.v4i2.1578.

Metty, Komang, Trisna Negara, and Hendra Wijaksana. 2012. “Analisa Performansi Sistem Pendingin Ruangan Dan Efisiensi Energi Listrik padaSistem Water Chiller Dengan Penerapan Metode Cooled Energy Storage.” Jurnal Energi Dan Manufaktur 4(1):4–11.

Mursito, Judhid Adi, I. Gusti Ketut Sukadana, and I. Gusti Ngurah Putu Tenaya. 2017. “Perancangan Dan Pengujian Alat Distilasi Minyak Dari Limbah Sampah Plastik.” Jurnal Ilmiah Teknik Desain Mekanika 6(4):311–17.

Nikhil Babu, P., D. Mohankumar, P. Manoj Kumar, M. Makeshkumar, M. Gokulnath, K. Gurubalaji, G. Harrish, and M. Ashok. 2021. “Energy Efficient Refrigeration System with Simultaneous Heating and Cooling.” Pp. 8188–94 in Materials Today: Proceedings. Vol. 45.

Ramadan, Haris. 2018. “Uji Prestasi Refrigeran R22 Pada Mesin Pendingin Kompresi Uap Dengan Metode Pengujian Aktual Dan Simulasi.” Konversi Energi Dan Manufaktur UNJ 5(2):74–81.

Rubianto, Budi, Rochmad Winarso, and Rianto Wibowo. 2018. “Rancang Bangun Kondensor Pada Destilator Bioetanol Kapasitas 5 Liter/Jam Dengan Skala Umkm.” Jurnal Crankshaft 1(1). doi: 10.24176/crankshaft.v1i1.2587.

Santosa, Tito Hadji Agung, Muhammad Nadjib, Thoharuddin, and Muhammad Akhid Riza. 2017. “Efek Variasi Beban Pendinginan Terhadap Coefficient Of Performance (COP) Alat Uji Pengukuran Koefisien Evaporasi Menggunakan Refrigeran R-134A .” Semesta Teknika 20(2):193–203.

Seftian, Deky, Ferdinand Antonius, and M. Faizal. 2012. “Pembuatan Etanol Dari Kulit Pisang Menggunakan Metode Hidrolisis Enzimatik Dan Fermentasi.” Jurnal Teknik Kimia 18(1):10–16.

Siagian, S. 2017. “Perhitungan Beban Pendingin Pada Cold Storage Untuk Penyimpanan Ikan Tuna Pada Pt . X.” Bina Teknika 13(1):139–49.

DOI: https://doi.org/10.31764/jau.v8i2.5239